saudiasebo.blogg.se - Modelling analysis using power world simulator

#MODELLING ANALYSIS USING POWER WORLD SIMULATOR HOW TO#
#MODELLING ANALYSIS USING POWER WORLD SIMULATOR GENERATOR#
#MODELLING ANALYSIS USING POWER WORLD SIMULATOR SERIES#

The story begins with a local tailor who ordered a piece of cloth from London. In 1665, there was an outbreak of the bubonic plague in the village of Eyam in England. One historical example shows how false control strategies can make the situation much worse. If not, an epidemic may quickly spread and become a serious threat to global health. These decisions have to be made quickly and effectively.

To halt the spread, should all transportation via planes, trains, and cars be temporarily stopped?.

Should a mass quarantine be imposed on a certain geographical area?.

Would mass vaccination help and in what amount of time?.

What is the right prevention or control strategy?.

#MODELLING ANALYSIS USING POWER WORLD SIMULATOR HOW TO#

Epidemics also affect the economy and society of both developed and developing countries.Īn emergency hospital in Camp Funston, Kansas during an influenza epidemic.įaced with the threat of disease, medical professionals and public health officials have to make decisions on how to prevent or stop the spread of epidemics, considering questions such as: Recent epidemic outbreaks of SARS, the flu, and Ebola continue to present a very dangerous threat to our public health. The 1918 flu pandemics, immediately after World War I, killed up to 100 million people. The plague pandemics in the Middle Ages, known as the Black Death, killed a third of the population in Europe. Infectious diseases and epidemics have been a steady issue for humanity over the course of history. Today, public health officials use mathematical modeling techniques to study the flu and other infectious diseases to predict their spread and make informed decisions about public health. Influenza, commonly known as the flu, can be at the very least an unpleasant experience, but it also claims a lot of casualties every year. You can subscribe to the channel to watch more videos.Surely you remember the last time you were stuck in bed with the flu. Here is a complete video tutorial for all the steps listed in this article. Video Tutorial on Load Flow Analysis using ETAP

Results after running Load Flow analysis are given below:.

Insert Low Voltage Circuit Breakers inside the Composite network and place them before the Lumped Loads.

Insert High Voltage Circuit Breakers at the indicated locations.

Connect the cables back to their original buses.

Open the Composite Network and move the elements from the dumpster into the Network1 window.

Insert a Composite Network and connect between Bus2 and Bus7.

Rubber band both branches connected to Bus2 and Bus7.

Insert a normally open Tie Breaker between Bus4 and Bus5.

Move elements from Dumpster and connect them to Bus1.

Copy elements T1, Bus2, Lump1, Cable1, T2, Bus4 and Lump2.

Extend the length of Bus1 towards the right side.

#MODELLING ANALYSIS USING POWER WORLD SIMULATOR GENERATOR#

Once the Generator has been connected and the input data has been entered, you may proceed to run a Load Flow Calculation.

Connect & proceed to enter required input data for LF.

Extend the length of Bus2 towards the right side.

Proceed to connect them and enter the required data.

Enter four more elements into the one-line diagram.

Once all the elements have been connected and the input data has been entered, you may proceed to run a Load Flow Calculation.

Enter four new elements into the one-line diagram and proceed to enter the input data for each element.

Power flow using ETAP Softwareįor building and simulating this power network, open ETAP and follow the steps. For an introduction to basics of ETAP and an overview of ETAP toolbars, there’s a tutorial Introduction to ETAP for Power System Modeling & Simulations . In this tutorial, we’ll show you how to build one-line diagram of a power network in ETAP and how to perform Load Flow Analysis of the system using Load Flow Toolbar.

#MODELLING ANALYSIS USING POWER WORLD SIMULATOR SERIES#

This tutorial series is based on using ETAP for Power System Modeling, Design and Analysis. ETAP is such an application for performing various analyses on simulated power networks. Various industry standard softwares are used for load flow studies. Load Flow results help in maintinaing proper operation of a Power System and also to design and extend the existing Power System. Load Flow (or Power Flow Analysis) is one of the most important analysis to be performed on a Power System.

Video Tutorial on Load Flow Analysis using ETAP.